Term
|
Definition
| This log measures the bulk resistivity (the reciprocal of conductivity) of the formation. Resistivity is defined as the degree to which a substance resists the flow of electric current. |
|
|
Term
|
Definition
| Resistivity is a function of porosity and pore fluid in a rock. Porous rock containing conductive fluid (such as saline water) will have low resistivity. A non-porous rock or hydrocarbon-bearing formation has high resistivity. |
|
|
Term
| What are Resistivity Logs used for? |
|
Definition
| This log is very useful for determining the type of fluids in formations and is frequently used as an indicator of formation lithology. |
|
|
Term
| Spontaneous Potential (SP) Logs |
|
Definition
| This log measures the electrical current that occurs naturally in boreholes as a result of salinity differences between the formation water and the borehole mud filtrate (formation and surface). |
|
|
Term
| What are SP Logs used for? |
|
Definition
| These logs are used as indicators of permeable beds (including determining permeable sands and impermeable shales) or for locating bed boundaries. The SP log was one of the first tools to be used to distinguish shale from sand in clastic sequences (zero matches pure shale while high SP values match sand). |
|
|
Term
|
Definition
| This log records the radioactivity of a formation. |
|
|
Term
| What are Gamma Ray Logs used for? |
|
Definition
| Sequence stratigraphic analysis |
|
|
Term
| How do Gamma Ray Logs work? |
|
Definition
| Shales (or clay-minerals) commonly have a relatively high gamma radioactive response, and consequently gamma ray logs are taken as good measures for grain size (and subsequently inferred depositional energy). Thus coarse-grain sand, which contains little mud, will have low gamma ray value, while a fine mud will have a high gamma ray value. The values range of gamma ray is measured in API (American Petroleum Institute) units and range from very few units (in anhydrite) to over 200 API units in shales. |
|
|
Term
|
Definition
| This log measures the porosity of a formation, indicating in its response the quantity of hydrogen present in the formation. The log is calibrated to limestone. The linear limestone porosity units are calibrated using the API Neutron pit in 19% porosity, water-filled limestone is defined as 1000 API units. |
|
|
Term
| What are Neutron Logs used for? |
|
Definition
| This log is useful in measuring lithology (usually in combination with Density Log). |
|
|
Term
|
Definition
| This log is a measure of the formation's bulk density and is mostly used as a porosity measure. Different lithologies can also be determined using Density log based on returned density value. For example, pure quartz will have a bulk density (g/cm-3) up to 2.65, coal 1.2-1.8, halite 2.05, limestone up to 2.75, dolomite up to 2.87, anhydrite 2.98. |
|
|
Term
| What are Density Logs used for? |
|
Definition
| Density is mostly commonly used in conjunction with Neutron logs to determine lithology of formation (density-neutron suites such as Schlumberger FDC-CNL suite). |
|
|
Term
|
Definition
| This log measures of the speed of sound in the formation, and is related to both the porosity and lithology of the rock being measured. |
|
|
Term
| What are Sonic Logs also known as? |
|
Definition
| Acoustic, p-wave, DT, Delta T |
|
|
Term
| What are Sonic Logs used for? |
|
Definition
Thus, if the lithology of a formation is know, this log can be used to determine its porosity. Shales have lower velocity (higher transit time) than sandstone of same porosity, making this log a good indicator of grain size.
Sonic log values (in ms/ft) for some rock types are: sandstone 51-56, limestone 47.5, dolomite 43.5, anhydrite 50, halite 67. |
|
|
