Term
|
Definition
Wrap a thin wire around the fiber and coaxial cables to secure them to the pole |
|
|
Term
|
Definition
A steel support wire to which the coaxial and fiber optic cables are lashed in aerial installations. 1/4 or 3/8 inch zinc coated steel support. |
|
|
Term
1/4 Inch Strand Mechanical properties |
|
Definition
weight (lb/ft) .121 Diameter .25 Ultimate breaking strength(lb) 3900 |
|
|
Term
3/8 Inch Strand Mechanical properties |
|
Definition
weight (lb/ft) .270 Diameter .375 Ultimate breaking strength(lb) 6900 |
|
|
Term
|
Definition
A loop intentionally formed in the cable to compensate for expansion and contraction caused by temperature changes |
|
|
Term
|
Definition
Strand that connects the pole line hardware to an anchor |
|
|
Term
|
Definition
Buried metal device used to transfer force from the pole to the ground |
|
|
Term
|
Definition
Is the general name for the guy wire and associated hardware on all guys
(downguy, Anchor Guy, Simple Guys) |
|
|
Term
|
Definition
May be used as a terminal guy or two can be used in a location where the strand changes directions.
AKA: Line Guys. |
|
|
Term
|
Definition
Used at the end of pole lines |
|
|
Term
|
Definition
Used at the end of pole lines |
|
|
Term
|
Definition
Used when the strand changes directions. It is in line with the angle that bisects the strand routing. |
|
|
Term
|
Definition
Used to establish clearance for the guys. Attached to a stub pole |
|
|
Term
|
Definition
A pole used for strand tensioning purposes. |
|
|
Term
|
Definition
Span Guy or Overhead guy
Utilizes an in-line pole as an anchor. |
|
|
Term
|
Definition
Uses a horizontal strut to provide overhead clearance when a head guy causes a hazzard to trafic beneath the guy. |
|
|
Term
|
Definition
Used when a straight pole line is subjected to extreme sideward forces typically in the form of wind. |
|
|
Term
|
Definition
Directly torqued, into the ground ith a power anchor driver (anchor cranker). |
|
|
Term
|
Definition
Designed for use in soft soil where screw anchors are less effective.
Also called Plate-type Anchors |
|
|
Term
|
Definition
Are designed to expand in holes bored in rock or concrete. Also called concrete anchors. |
|
|
Term
|
Definition
A coring tool used for QR cable that removes the cables jacket and sheath hile also coring the cable |
|
|
Term
|
Definition
The device, usually a screw, used to connect the coaxial cable's center conductor to an active or passive device. |
|
|
Term
|
Definition
Having a saw-toothed edge or margin notched with toothlike projections. |
|
|
Term
|
Definition
Uses a mechanical wrenching action to bend expansion loops into coaxial cable prior to lashing or during splicing. |
|
|
Term
|
Definition
Is used to measure the pulling tension applied to cables |
|
|
Term
|
Definition
Allos cables that are being pulled to swivel and are used to ensure that the cables are not over tensioned during pulling. It will unlink when a specified tension is exceeded. |
|
|
Term
|
Definition
Used to support multiple cables in independent rollers. |
|
|
Term
|
Definition
Used to support a single cable prior to lashing and may be used when cables are lashed directly to strand or in over lash applications. |
|
|
Term
|
Definition
Used to install self-support cable and is attached to the pole hardware to support the cable as it is pulled out. |
|
|
Term
|
Definition
Used to support a single cable prior to lashing and depending on the acutal block, may be used when cables are lashed directly to strand or in overlash applications. |
|
|
Term
|
Definition
Is used to route cables through inside or outside corners up to 90 degrees. It minimizes drag on the cable in corners and ensures that the minimum bend radius of the cable is not exceeded. |
|
|
Term
|
Definition
Used to route cables through inside or outside corners up to 45 degrees. It minimizes drag on the cable in corners and ensures that the minimum bend radius of the cable is not exceeded. |
|
|
Term
|
Definition
Is used to guide cables from the cable trailer or reel stand to the strand. |
|
|
Term
|
Definition
Is used to support both 45 & 90 degree corner blocks or set-up chutes at mid-span |
|
|
Term
|
Definition
Is used to lash cable directly to installed strand or cable bundles. |
|
|
Term
|
Definition
Allows multiple cables to be pulled into place when lashing cables directly to strand. |
|
|
Term
|
Definition
Allows multiple cables to be pulled into place in overlash applications.. Allows pulled cables to independently swivel. |
|
|
Term
|
Definition
Is used to push equipment ahead of a pulled lasher. It is also know as a shotgun or a shuttle. |
|
|
Term
Cable Positioner (Magic Box) |
|
Definition
A cable positioner is pushed in front of a lasher by a cable block pusher to uniformly position multiple cables that are being lashed. |
|
|
Term
|
Definition
Is used to guide the cable into the lasher in drive-off applications. It can be used for new strand or overlash applications. |
|
|
Term
|
Definition
A fiberglass stick used to lift cable blocks and cables into place utilizing the appropriate type of lay-up stick heads. |
|
|
Term
Cable Lifter (lay-up Stick Head) |
|
Definition
Is used in conjunction ith a lay-up stick to lift cables into place. THe lifter ensures that the cables being lifted are not damaged, by exceeding minimum bend radii |
|
|
Term
|
Definition
The resistance of a circuit to alternating current. Measured in ohms, but can not be measured with the ohm portion of a volt-ohm meter |
|
|
Term
|
Definition
Straps Installed loosely by hand spaced a minimum of 4 inches from the end of any bend in the cable.
If the span is 250ft or longer place 2 expansion loops on each pole.
If there is an obstruction at the pool the loop may need to be further out from the pole.
Input and output expansion loops exist at all turns and corners of 45 to 90 degrees
When ever the cable changes height at the pole or the strand is double dead-ended install both input & output loops
Install all splitters and DC's on the input side of the pole with expansion loops on the output side |
|
|
Term
|
Definition
When the loop location is dictated by the signal flow direction of the feeder cable. |
|
|
Term
|
Definition
A double dead end is when two perpendicular strands end at the same pole |
|
|