Term
|
Definition
| also called bonding, balancing, and aggregation—is a technology that has been available for some time, but was always tied to specific hardware implementations. The NIC teaming capability in Windows Server 2012 R2 is hardware independent and enables you to combine multiple physical network adapters into a single interface. The results can include increased performance by combining the throughput of the adapters and protection from adapter failures by dynamically moving all traffic to the functioning NICs. |
|
|
Term
|
Definition
| After you install roles on your servers, the roles appear as icons Server Manager’s the navigation pane. These icons actually represent role groups. Each role group contains all instances of that role found on any of your added servers. You can therefore administer the role across all servers on which you have installed it. |
|
|
Term
Which features must you remove from a full GUI installation of Windows Server 2012 R2 to convert it to a Server Core installation? (Choose all that apply)
a. Windows Management Instrumentation
b. Graphical Management Tools and Infrastructure
c. Desktop Experience
d. Server Graphical Shell |
|
Definition
|
|
Term
Which of the following NIC teaming modes provides fault tolerance and bandwidth aggregation?
a. Hyper-V live migration
b. Switch Independent Mode
c. Switch Dependent Mode
d. Link Aggregation Control Protocol |
|
Definition
|
|
Term
Which of the following command-line tools do you use to join a computer to a domain?
a. Net.exe
b. Netsh.exe
c. Netdom.exe
d. Ipconfig.exe |
|
Definition
|
|
Term
Which of the following statements about Server Manager is not true?
a. Server Manager can deploy roles to multiple servers at the same time.
b. Server Manager can deploy roles to VHDs while they are offline.
c. Server Manager can install roles and features at the same time.
d. Server Manager can install roles and features to any Windows Server 2012 R2 server on the network. |
|
Definition
|
|
Term
Which of the following operations can you not perform on a service using Server Manager? (Choose all that apply)
a. Stop a running service
b. Start a stopped service
c. Disable a service
d. Configure a service to start when the computer starts |
|
Definition
|
|
Term
Name the two methods to assign a static IP address to a computer using Server Core.
a. Server Manager and the netdom.exe command
b. The netdom.exe command and the IPv4 Properties sheet
c. The IPv4 Properties sheet and the netsh.exe command
d. The netsh.exe command and the New-NetIPAddress cmdlet provided by Windows PowerShell |
|
Definition
|
|
Term
Before you can deploy roles to multiple remote servers, what must be done?
a. Perform an in-place upgrade to Windows Server 2012 R2.
b. Ensure the remote servers are patched sufficiently.
c. Add the remote servers to the Server Manager interface.
d. Perform a full backup |
|
Definition
|
|
Term
What utility allows you to install components to multiple servers at once?
a. The Add Roles and Features Wizard only
b. Both Add Roles and Features Wizard and Windows PowerShell
c. Windows PowerShell only
d. The Minimal Server Interface |
|
Definition
|
|
Term
What method is available to install roles and features on another Windows Server 2012 computer using Windows PowerShell?
a. Use the Install-WindowsFeature command and an exported configuration file
b. Use the Install-WindowsRole command and an exported configuration file
c. Use Server Manager and the proper tile
d. It is not possible using Windows PowerShell |
|
Definition
|
|
Term
What is the key principle to delegating server administrative tasks?
a. Granting individuals the tasks they feel most comfortable doing
b. Granting individuals only the permissions needed to do the delegated job
c. Assign the delegated tasks to the person most likely to benefit
d. Assigning enough permissions to do the delegated tasks as well as anticipated tasks |
|
Definition
|
|
Term
Best Answer:
On a Windows Server 2012 R2 server, you decide to change the interface. Select the best answer to convert a GUI server to Server Core.
a. Reinstall the operating system and select Server Core upon installation
b. Use Server Manager to start the Remove Roles and Features Wizard
c. Use Server Manager to deselect the Server Graphical Shell option
d. There is no option to downgrade from GUI to Server Core |
|
Definition
|
|
Term
Best Answer:
Windows Server 2012 R2 provides hardware-independent NIC teaming or bonding to enable better network performance and adapter fault-tolerance. However, in what scenario is the NIC teaming limited?
a. During a Hyper-V live migration
b. When network adapters connect to different switches
c. When network traffic consists of large TCP sequences
d. For multiple network adapters to function as one interface |
|
Definition
|
|
Term
Best Answer:
As an administrator of a Windows Server 2012 R2 network, you want to add a role to a few servers on the network. What is your best available option?
a. Install a role at the target server’s console
b. Use Server Manager on the nearest computer running Windows Server 2012 R2
c. Connect to the target server using Remote Desktop Services
d. Using PowerShell, install the desired role to all target servers at once |
|
Definition
|
|
Term
Best Answer:
What is the advantage of deploying roles to a virtual hard disk (VHD) file?
a. Administrators can use Server Manager to modify VHD files
b. An administrator can modify server roles to offline virtual machines (VMs) without starting the VM
c. An administrator can modify server roles to offline VMs without connecting the VM to the network
d. VHD files require fewer resources (for example, hard drive space) |
|
Definition
|
|
Term
Best Answer:
What is the key benefit behind delegating server administration?
a. In larger networks, delegation uses permissions to restrict access
b. In smaller networks, delegation provides formalized synergy
c. In larger networks, delegation improves prioritization of tasks
d. In smaller networks, delegation creates employment opportunities |
|
Definition
|
|
Term
| Build a List:
You have finished a new installation. Order the steps to rename the computer and join it to a domain using the command prompt.
a. Type netdom join %ComputerName%
/domain:
/userd: /passwordd:*
b. Restart the computer by typing shutdown /r
c. Ensure DHCP has already configured the computers TCP/IP client
d. Type netdom renamecomputer %ComputerName%
/NewName: |
|
Definition
|
|
Term
Build a List:
Order the steps to install a role or feature using Server Manager.
a. Select the destination server
b. Choose the Select Installation Type (Role-based or Feature-based installation selected)
c. Add required features or services the needed service depends upon
d. Log on with administrative privileges and start Server Manager
e. Select the server role
f. From the Manage menu, select Add Roles and Features |
|
Definition
|
|
Term
Build a List:
Order the steps to install a role or feature to an offline VHD file.
a. From the Manage menu, select Add Roles and Features
b. Choose the Select Installation Type (Role-based or Feature-based installation selected)
c. Log on with administrative privileges and start Server Manager
d. For Destination server, select Virtual Hard Disk
e. Close the wizard to dismount the VHD
f. Type in or browse to the location of the VHD file you want to modify
g. Select the role and required features |
|
Definition
|
|
