The first items I will cover are the points of performance.  Your first point of performance is PROPER EXIT, CHECK BODY POSITION, AND COUNT.  “JUMPERS HIT IT.”  Upon exiting the aircraft, snap into a good tight body position.  Keep your eyes open, chin on your chest, elbows tight into your sides, place your hands over the end of the reserve, with your fingers spread, bend forward at the waist, keeping your feet and knees together, knees locked to the rear, and count to four thousand.

At the end of your four thousand, count immediately go into your second point of performance.  CHECK CANOPY AND GAIN CANOPY CONTROL.  When jumping the T-10 series parachute reach up to the elbow locked position and secure a set of risers in each hand, simultaneously conduct a 360- degree check of your canopy. When jumping the MC-6 series parachute secure a toggle in each hand and pull them down to eye level.  Simultaneously conduct a 360 degree check of your canopy.  If during your second point of performance you find that you have twists.  Reach up and grasp a set of risers in each hand, thumbs down, and knuckles to the rear.  Pull the risers apart and begin a vigorous bicycling motion.  When the last twist comes out, immediately check canopy and gain canopy control.

Your third point of performance is KEEP A SHARP LOOKOUT DURING YOUR ENTIRE DESCENT.   Remember the three rules of the air and repeat them after me.  Always look before you slip or turn, always slip or turn in the opposite direction to avoid collision, and the lower jumper always has the right of way.  Avoid fellow jumpers all the way to the ground and maintain a 25 foot separation when jumping the T-10 series parachute and a 50 foot separation when jumping the MC-6 series parachute.  At the end of your third point of performance, release all appropriate equipment tie downs. (NOTE:  When jumping the MC-6 series parachute you will transfer control of one toggle to the opposite hand, so that the other hand is controlling both toggles, with your free hand release all appropriate equipment tie downs.)

This brings you to your fourth point of performance which is PREPARE TO LAND.  At 100-200 ft AGL look below you to ensure that there are no fellow jumpers and lower your equipment.  Regain canopy control.  At approximately 100 ft AGL slip or turn into the wind and assume a landing attitude.  When jumping the T-10 series parachute and the wind is blowing from your left, reach up on left set of risers and pull them deep into your chest.  If the wind is blowing from your front, reach up on front set of risers and pull them deep into your chest.  If the wind is blowing from your right, reach up on right set of risers and pull them deep into your chest.  If the wind is blowing from your rear, reach up on rear set of risers and pull them deep into your chest.  Once you are facing into the wind, assume a landing attitude by keeping your feet and knees together, knees slightly bent, with your head and eyes on the horizon.

When jumping the MC-6 series parachute at approximately 250 ft AGL, determine your direction of drift.  If the wind is blowing from your left, pull your left toggle down to the elbow locked position.  When you are facing into the wind let up slowly to prevent oscillation.  If the wind is blowing from your right, pull your right toggle down to the elbow locked position.  When you are faced into the wind let up slowly to prevent oscillation.  If the wind is blowing from your rear, pull either toggle down to the elbow locked position.  When you are facing into the wind let up slowly to prevent oscillation.  If the wind is blowing from your front make minor corrections to remain facing into the wind.  Look below you to ensure there are no fellow jumpers.  Transfer control of one toggle to the opposite hand, so that the other hand is controlling both toggles.  With the free hand release all appropriate equipment tie downs and lower your combat equipment.  Now regain canopy control with both hands.  Assume a proper prepare to land attitude by pulling toggles to the appropriate breaking position, keeping your feet and knees together, knees slightly bent, elbows rotated in toward your sides, with your head and eyes on the horizon.

When the balls of your feet make contact with the ground, you will go into your fifth point of performance, LAND.  You will make a proper PLF by hitting all five points of contact.  Touch them and repeat them after me.  1) BALLS OF THE FEET. 2) CALF. 3) THIGH. 4) BUTTOCKS. 5) PULL UP MUSCLE.  You will never attempt to make a stand up landing.

  Remain on your back and activate one of your canopy release assemblies by using either the hand to shoulder method or the hand assist method.  To activate your canopy release assembly using the hand to shoulder method, with either hand reach up and secure a safety clip and pull it out and down exposing the cable loop.  Insert thumb from bottom to top through the cable loop, turn your head in the opposite direction and pull out and down on the cable loop.  To activate your canopy release assembly using the hand assist method, with either hand reach up and secure a safety clip and pull out and down exposing the cable loop.  Insert your thumb from bottom to top. Re-enforce that hand with the other hand, turn your head in the opposite direction and pull out and down on the cable loop.  If your canopy fails to deflate, activate the other canopy release assembly.  Place your weapon into operation and remain on your back to get out of the parachute harness.

Pre-Jump VII

Mod#2

I will now cover RECOVERY OF EQUIPMENT.

  Once out of the parachute harness, remove all air items from the parachute harness.  Roll the aviator’s kit bag two thirds down and place the parachute harness inside the aviator’s kit bag smooth side facing up, leaving the waistband exposed.  Remain on a knee and begin pulling the suspension and canopy to the aviator’s kit bag, stuffing them into the aviator’s kit bag as you go.  Route the waistband through the bridal loop leaving six to eight inches of the waistband exposed and snap, do not zip, the aviator’s kit bag.  Secure the reserve parachute to the aviator’s kit bag.  Place it over your head, conduct a 360-degree police of your area and move to the assembly area.

I will now cover TOWED JUMPER PROCEDURES.

  “JUMPERS HIT IT.”  If you become a towed jumper and are being towed by your static line and are unconscious, you will be retrieved inside the aircraft.  If you are conscious, maintain a good tight body position with your left hand over the end of the reserve and with your right hand over the rip cord protector flap, while resting the right forearm on the rip cord grip, and an attempt will be made to retrieve you inside the aircraft.

  As you near the jump door, DO NOT REACH FOR US, continue to protect your ripcord grip (Rip Cord Handle, MC-6).  If you cannot be retrieved, you will be cut free.  Once you feel yourself falling free from the aircraft, immediately activate your reserve parachute for a total malfunction.

  If you are being towed by your equipment, regardless of whether you are conscious or unconscious, we will cut or jog your equipment free and main parachute will deploy.

NOTE:  If you are being towed from a rotary wing aircraft, maintain a good tight body position and protect your ripcord grip (Rip Cord Handle MC-6).  The aircraft will slowly descend to the DZ, come to a hover and the jumpmaster will free you from the aircraft.

The next item I will cover is MALFUNCTIONS.

  There are two types of malfunctions, total and partial.  A total malfunction provides no lift capability what so ever; therefore, you must activate your reserve using the PULL DROP METHOD.  While cigarette rolls and streamers are partial malfunctions, they provide no lift capability and you must activate your reserve using the PULL DROP METHOD.

  There are several types of partial malfunctions and actions for each.  If you have broken suspension lines, blown sections or gores, compare your rate of descent with fellow jumpers.  If you are falling faster than fellow jumpers, activate your reserve for a partial malfunction.  If you have a squid, semi-inversion, or a complete inversion with damage to the canopy or suspension lines you must immediately activate your reserve for a partial malfunction.  If you have a complete inversion with no damage to the canopy or suspension lines, do not activate your reserve parachute.

I will now cover ACTIVATION OF THE MODIFIED IMPROVED RESERVE PARACHUTE SYSTEM SOFT LOOP CENTER PULL.

  To activate the MIRPS SLCP; you will use the “PULL DROP METHOD.”, “JUMPERS HIT IT.”  Maintain a good tight body position.  Grasp the left carrying handle with your left hand; with your right hand grasp the ripcord grip.  Pull up and out on the ripcord grip and drop it.  Your reserve will activate.

I will now cover ACTIVATION OF THE T-11 RESERVE PARACHUTE SYSTEM.

  To activate the T-11; you will use the “PULL DROP METHOD”, “JUMPERS HIT IT.”  Maintain a good tight body position. With either hand grasp the ripcord handle.  Throw your head back and pull out on the ripcord handle and drop it.  Your reserve will activate.  NOTE; If you have to activate the reserve for a total malfunction, let up on the risers for the reserve.  Pull a good two riser slip opposite your direction of drift during your fourth point of performance.

NOTE;If you have to activate the reserve for a partial malfunction, any attempt to control either canopy will be useless as one canopy will act as a brake for the other.

The next items I will cover are COLLISIONS AND ENTANGLEMENTS.

  “JUMPERS HIT IT. CHECK CANOPY AND GAIN CANOPY CONTROL.”  If you see another jumper approaching, immediately attempt to slip or turn away.  If you cannot avoid the collision assume a spread eagle body position and attempt to bounce off the jumper’s canopy and suspension lines and immediately slip or turn away.  If you pass through the suspension lines, snap into a modified position of attention.  With your right hand protect the ripcord grip and with your left hand attempt to weave your way out of the suspension lines the same way you entered and then slip or turn away.

If you become entangled and are jumping the T-10 series parachute, the higher jumper will climb down to the lower jumper using the hand under hand method.  Once both jumpers are even, you will face each other and grasp each other’s left main lift web with your left hand.  Both jumpers will discuss which PLF to execute.  Both jumpers will conduct the same PLF.  Neither jumper will execute a front PLF.  Both jumpers will continue to observe their canopies.  If one canopy collapses, neither jumper will activate their reserve as one T-10 series parachute can safely deliver two combat equipped jumpers to the ground.  If both canopies collapse the jumpers will pull towards each other to create a clear path for the activation of their reserve parachutes, and then activate their reserves using the PULL DROP METHOD.

  If you are jumping the MC-6 series parachute, both jumpers will remain where they are, obtain a clear path and immediately activate their reserve parachutes using the PULL DROP METHOD.

Pre-Jump XIII

Mod#3

If you become entangled and are jumping the T-10 series parachute, the higher jumper will climb down to the lower jumper using the hand under hand method.  Once both jumpers are even, you will face each other and grasp each other’s left main lift web with your left hand.  Both jumpers will discuss which PLF to execute.  Both jumpers will conduct the same PLF.  Neither jumper will execute a front PLF.  Both jumpers will continue to observe their canopies.  If one canopy collapses, neither jumper will activate their reserve as one T-10 series parachute can safely deliver two combat equipped jumpers to the ground.  If both canopies collapse the jumpers will pull towards each other to create a clear path for the activation of their reserve parachutes, and then activate their reserves using the PULL DROP METHOD.

  If you are jumping the MC-6 series parachute, both jumpers will remain where they are, obtain a clear path and immediately activate their reserve parachutes using the PULL DROP METHOD.

If you get hung up in the trees KEEP YOUR ADVANCED COMBAT HELMET ON and lower and jettison all unneeded equipment.  Activate the chest strap ejector snap and activate the quick release in your waistband.  Place your left hand over the ripcord protector flap and apply pressure.  Grasp the ripcord grip with your right hand and pull it and drop it.  Control the activation of the reserve parachute towards the ground ensuring that all suspension lines are completely deployed.  Disconnect the left connector snap and rotate the reserve to the right.  Grasp the main lift web with either hand below the canopy release assembly and with the other hand activate the leg strap ejector snaps and climb down the outside of the reserve.  Remember when in doubt, stay where you are and wait for assistance.

If you are jumping the MC-6 and get hung up in the trees KEEP YOUR ADVANCED COMBAT HELMET ON and lower and jettison all unneeded equipment.  Activate the quick release in the chest strap and the waistband.  Ensure you have a clear and unobstructed path to activate your reserve.  First remove the top tuck tab and insert either hand from top to bottom behind the ripcord handle and apply steady inward pressure.  With the opposite hand grasp the soft handle, pull out and drop it.  Now control the activation of the reserve all the way down to the ground.  Ensure all canopy and suspension lines are free of the pack tray, and that the reserve reaches close to the ground for you to safely climb down.  DISCONNECT THE LEFT CONNECTOR SNAP FROM THE LEFT D RING, AND REATTACH IT TO THE RIGHT TRIANGLE LINK.  Seat yourself well into the saddle and grasp the main lift web with either hand below the canopy release assembly.  With the other hand activate the leg strap ejector snaps and climb down the outside of the reserve.  Remember, when in doubt, stay where you are and wait for assistance.  NOTE: The T-11 reserve suspension lines have a protective coating and are very slippery.  Extra care must be taken when climbing down.

The next emergency landing I will cover is the Wire Landing.  If you are drifting towards the wires, slip or turn away.  If you cannot avoid the wires, look below you to ensure there are no fellow jumpers and lower and jettison your equipment making a mental note of where it lands.  Assume a landing attitude by placing your hands, fingers, and thumbs extended and joined high on the inside of the front set of risers with the elbows locked.  Place your chin on your chest, keep your feet and knees together and exaggerate the bend in your knees.  When the balls of your feet make contact with the wires, begin a vigorous rocking motion in an attempt to pass all the way through the wires.  Be prepared to conduct a PLF if you pass all the way through the wires.  If you get hung up in the wires, stay where you are and wait for assistance.

The next emergency landing I will cover is the Water Landing.  The water landing is the most dangerous emergency landing because it takes the most time to prepare for.  If you are drifting towards a body of water, immediately slip or turn away.  If you cannot avoid the water, look below you to ensure there are no fellow jumpers and lower; do not jettison your equipment.  Next, jettison your Advanced Combat Helmet.  Activate the quick release in your waistband, disconnect the left connector snap and rotate the reserve to your right.  Seat yourself well into the saddle and activate the chest strap ejector snap.  Regain canopy control.  Prior to entering the water assume a landing attitude by keeping your feet and knees together knees slightly bent and place your hands on the leg strap ejector snap, head and eyes on the horizon.  When the balls of your feet make contact with the water, activate the leg strap ejector snaps, arch your back, throw your arms above your head and slide out of the parachute harness.  Swim upstream or upwind away from the canopy.  Be prepared to execute a PLF if the water is shallow.  If the canopy comes down on top of you locate a radial tape, follow it to the skirt of the canopy and swim upstream or upwind away from the canopy.  NOTE:  When jumping the MC-6 series parachute system for water landings you will activate the quick release in the chest strap and waistband.  Disconnect the left connector snap and rotate the reserve down to the right.

The next items I will discuss are MISSION ORIENTED items.

  If you are jumping the B-7 life preserver, activate it in the air.  Lower but do not jettison combat equipment.

  NIGHT JUMPS:  When conducting night jumps, be sure to give your canopy an extra look, and maintain noise and light discipline all the way to the ground.

  AWADS:  When jumping under AWADS conditions, do not lower your equipment until you have passed through the clouds. Do not slip or turn unless you have to avoid collision.  If you have any type of malfunction, you must immediately activate your reserve using the pull drop method because you cannot compare your rate of descent with fellow jumpers.  Ensure you recheck your canopy once you pass through the clouds.

  PLF’S:  We will now move to the PLF platform and conduct one satisfactory PLF in each of the four directions ensuring you conduct a proper PLF.